Transmedia SW 15 - Scissors for Kevlar | Cuts Kevlar and Aramid fiber

NFO Kevlar / aramid shears

NFO Heat-shrinking sleeve, diameter 50mm, length 14,2cm - Used to protect and seal I / O on fiber optic cable, but also to stiffen the cable inserted in the holes in the splice closures | Shrink ratio: 2: 1 to 3: 1

NFO Heat-shrinking sleeve, diameter 40mm, length 14,2cm - Used to protect and seal I / O on fiber optic cable, but also to stiffen the cable inserted in the holes in the splice closures | Shrink ratio: 2: 1 to 3: 1

NFO Heat-shrinking sleeve, diameter 30mm, length 14,2cm - Used to protect and seal I / O on fiber optic cable, but also to stiffen the cable inserted in the holes in the splice closures | Shrink ratio: 2: 1 to 3: 1

NFO Cutter for fiber optic cables 1.5-3.3 mm - 4 channels for tubes / cables with different diameters: 1.5-1.9 mm | 2.0-2.4 mm | 2.5-2.9 mm | 3.0-3.3 mm

NFO Stripper with 3 holes to remove the buffer and other external coatings of the fiber optic cable without damaging the fiber - outer coating 2-3mm | buffer 900 µm to 250µm | 250µm to 125µm varnish

NFO Optical power meter - The APM65C meter is a device designed for quick and easy testing of optical power in PON networks. Calibration for wavelengths 850nm, 1300nm, 1310nm, 1490nm, 1550nm, 1625nm allows work with single-mode and multi-mode fibers. The meter's measurement range is -50 to +26 dBm , measurement accuracy is 0.15dB , and resolution is 0.01dB | PON network testing | Measurement range: +26 ~ 50dBm | Measurement accuracy: 0.15dB | Resolution : 0.01dB | Calibrated wavelengths: 850nm / 1300nm / 1310nm / 1490nm / 1550nm / 1625nm | Connector: SC or FC | Power supply: AA*2 batteries | Battery life: up to 160h | Dimensions: 107x50x28 mm | Weight: 70 | Operating temperature: -10 ° C - 50 ° C | Integrated LED night light

NFO Clamp for round cables, diameter 13-16 mm, 16kN - designed for hanging round self-supporting cables | The task of extraction holders is to strain the ADSS cables between the poles. The handle can be used on any type of brackets thanks to the removable cord | high quality thermoplastic and mechanical resistance as well as weather conditions, resistant to UV | Minimum breaking load: 17.5 kN | Lengthened rope: 520 mm | Body length: 200 mm

NFO Clamp for round cables, diameter 8-12 mm, 16 kN - designed for hanging round self-supporting cables | high quality thermoplastic and mechanical resistance as well as weather conditions, resistant to UV | Minimum breaking load: 17.5 kN | Lenth length with cable: 700 mm | Length of the body: 200 mm

NFO Clamp for round cables, diameter 3-7 mm, 3 kN - designed for hanging round self-supporting cables | high quality thermoplastic and mechanical resistance as well as weather conditions, resistant to UV | Cable length: 380mm | Mechanical strength: 3kN

NFO Clamp for round cables, diameter 3-5,5mm, 2.3 kN - high quality thermoplastic and mechanical resistance as well as weather conditions, resistant to UV | Minimum breaking load: 2.3kN

NFO LC Connector cleaner - tool for cleaning fiber optic connectors (LC) | The cleaning itself is carried out easily and quickly by pressing the device | Cleaning does not require the use of alcohol | The process itself is carried out by shifting the thread, made of microfiber and having antistatic properties, thanks to which no dirt appears on the joint | Capacity: up to 750 cleanings

NFO SC/ST/FC Connector cleaner - tool for cleaning fiber optic connectors (SC/ST/FC) | The cleaning itself is carried out easily and quickly by pressing the device | Cleaning does not require the use of alcohol | The process itself is carried out by shifting the thread, made of microfiber and having antistatic properties, thanks to which no dirt appears on the joint | Capacity: up to 750 cleanings

NFO Tube cutter 3-32mm - Tool for cutting longitudinal fiber optic tubes and outer shell. It has a smooth adjustment from 3 mm to 32 mm.

NFO Clamp for round and flat DROP cables 2-5 mm, 900N | High quality thermoplastic material, mechanical resistance and weather conditions, UV resistant | Tool-free assembly ensures quick and efficient installation

NFO Splice Sleeve 2,8 mm, length 60 mm - 100 kom | Sheath length: 60 mm | Shank opening diameter: 1.4 mm +/- 0.1 mm | Outer sheath diameter: 2.8 mm +/- 0.3 mm | Reinforcement bar diameter: 1.2 mm | Minimum shrinking temperature: 90 [° C] | Shrinking time: about 2 minutes (at temp. 110 [° C])

NFO Splice Sleeve 2,8 mm, length 45 mm - 100 kom | Shank opening diameter: 1.4 mm +/- 0.1 mm | Outer diameter of shrink sleeve after shrinking: 2.8 mm +/- 0.3 mm | Reinforcement bar diameter: 1.2 mm | Minimum shrinking temperature: 90 [° C] | Shrinking time: about 2 minutes (at temp. 110 [° C])

NFO Splice Sleeve 2,5 mm, length 45 mm - 100 kom | Sheath length: 45 mm | Sheath opening diameter: 1.3 mm +/- 0.1 mm | Outer sheath diameter: 2.5 mm +/- 0.3 mm | Reinforcement bar diameter: 1.2 mm | Shrink temperature minimum: 90 [ ° C] | Shrink time: about 2 minutes (at temp. 110 [° C])

NFO Splice Sleeve 2,5 mm, length 60 mm - 100 kom | Sheath length: 60 mm | Sheath opening diameter: 1.3 mm +/- 0.1 mm | Outer sheath diameter: 2.5 mm +/- 0.3 mm | Reinforcement bar diameter: 1.2 mm | Shrink temperature minimum: 90 [ ° C] | Shrink time: about 2 minutes (at temp. 110 [° C])

NFO 11-hole crossbar (bracket) with adjustable mounting on a rectangular pole - The construction of the set enables, among others, mounting all types of extraction, through and screw holders. Adjustable mounting system in the range of 100-500 mm will allow installation of the crossbar on most rectangular columns. The crossbar is screwed to two angles (fastening to the pole) with two screws. The angles have special holes that allow mounting the set to the pole using two metal bands (maximum width of the band - 20 mm) | In the set: 11-hole crossbar, Adjustable mounting system (angles), Mounting screws: M14 (x2), Nuts: M14 (x2) | Bracket dimensions:Length 440 mm | Width: 40 mm | Height: 40 mm | Thickness: 4 mm | Number of holes: 2x11 | Hole diameter: 16 mm

NFO Cable rack 500 mm - fiber optic cable rack is designed for collecting and organizing the supply of linear cable with different diameters. Racks guarantee functionality and the correct bending radius of the cable. They are used in cable rooms or telecommunications wells. They are made of high quality aluminum alloys. | 30x5mm high quality aluminum flat bars, mechanical resistance and weather conditions, UV resistant | 500x500mm | Middle threaded hole for mounting the tray: M6 | Mounting holes o10 | Weight: 0.8 kg

NFO OTDR Grandway FHO5000-D26, 1310/1550 SM - Dynamic Range (dB): 26/24 | Event/Attenuation Dead-zone (m): 0.8/4 | IP65 protection level, outdoor enhanced | 7-inch anti-reflection LCD screen | Support multi-language display and input | Testing Modes: Visual fault locator: Visible red light for fiber identification and troubleshooting, Light source: Stabilized Light Source (CW, 270Hz, 1kHz, 2kHz output), Field microscope probe | Testing Distance Single mode: 100m, 500m, 2km, 5km, 10km, 20km, 40km, 80km, 120km, 160km, 240km |

NFO Dust-free wipes for cleaning optical fiber cables, 280 pcs

NFO Laser light source, fault locator, power 30mW - The light source is a laser device used for quick and easy testing of fiber optic path continuity. The device is powered by two AA batteries or via an AC / DC power adapter (not included). The set includes a protective cover | Weight: 170g | Dimensions: 175mm x 26mm x 26mm | Wavelength: 650nm | Output power:> 30mW | The length of the tested section up to: 25 km | Connector: FC, ST, SC | Power supply: 2x AA battery or AC / DC power adapter (not included). | Working time on battery pack:> 40H (1mW) | Working temperature: 0 ~ + 60 ?

NFO Laser light source, fault locator, power 1mW - The light source is a laser device used for quick and easy testing of fiber optic path continuity. The device is powered by two AA batteries or via an AC / DC power adapter (not included). The set includes a protective cover | Weight: 170g | Dimensions: 175mm x 26mm x 26mm | Wavelength: 650nm | Output power:> 1mW | The length of the tested section up to: 5 km | Connector: FC, ST, SC | Power supply: 2x AA battery or AC / DC power adapter (not included). | Working time on battery pack:> 40H (1mW) | Working temperature: 0 ~ + 60 ?

NFO Fiber Cleaver T-901 - used to level the surface of the optical fiber before its joining / welding in welding machines. A protective cover is included | Weight: 310g | Dimensions: 54mm x 58mm x 58mm | Fiber type: 0.25 ~ 0.9mm | Coating diameter: 125µm | Cutting length: 9 ~ 16mm (0.25mm) 10 ~ 16mm (0.9mm) | Cutting angle: ?0.5 ° | Blade life : 40,000 cuts

NFO Fiber Cleaver T903 - used to level the surface of the optical fiber before its joining / welding in welding machines. A protective cover is included | Weight: 450g | Dimensions: 76mm x 63mm x 63mm | Fiber type: 0.25 ~ 0.9mm | Coating diameter: 125µm | Cutting length: 9 ~ 16mm (0.25mm) 10 ~ 16mm (0.9mm) | Cutting angle: less than 0.5 ° | Blade life : 48,000 cuts

NFO Laser light source, fault locator, power 20mW - The light source is a laser device used for quick and easy testing of fiber optic path continuity. The device is powered by two AA batteries or via an AC / DC power adapter (not included). The set includes a protective cover | Weight: 170g | Dimensions: 175mm x 26mm x 26mm | Wavelength: 650nm | Output power:> 20mW | The length of the tested section up to: 17 km | Connector: FC, ST, SC | Power supply: 2x AA battery or AC / DC power adapter (not included). | Working time on battery pack:> 40H (1mW) | Working temperature: 0 ~ + 60 ?

NFO Adjustable mounting of the crossbar on the rectangular pole, prodaje se u paru