ExtraLink POE-24-24W, 100mb/s Power-over-Ethernet (PoE) power supply 24V, 1A, 24W, AC cable included. It provides DC power for PoE-equipped device by "Injecting" DC power through the ethernet cable. It is compatible with Ubiquiti and MikroTik RouterBoard, AP's and other equipment supporting the standard PoE pinout. DC Grounded. Euro AC cord with ground wire included.
ExtraLink POE-24-24W-G, Gigabit Power-over-Ethernet (PoE) power supply 24V, 1A, 24W, Gigabit, AC cable included. It provides DC power for PoE-equipped device by "Injecting" DC power through the ethernet cable. It is compatible with Ubiquiti and MikroTik RouterBoard, AP's and other equipment supporting the standard PoE pinout. DC Grounded. Euro AC cord with ground wire included.
MaxLink POE-AFA-1, MaxLink pasivna POE injector, Passive PoE injector is used to power most RouterBoards, can be used to power any device with an appropriate input power connector. PoE Injector does not meet spec IEEE 802.3af.
MaxLink MAXPI15, PoE injector - 802.3af, 48V, 0.32A, 15,4W, 1Gbit, power cord. Gigabit PoE injector with very good quality and one output POE port for powering devices supporting 802.3af with maximum power consumption up to 15,4W. The power supply is guided over 4,5 (+) and 7,8 (-) wires.
MikroTik GPER, Gigabit Passive Ethernet Repeater. The GPeR unit allows to extend Ethernet cable by additional hop (< 100 - 150 m to regular network devices, and up to 210 m to another GPeR unit) up to 1,500 m. Maximium allowed length of CAT6 Ethernet cable between GPeR and power source/router is up to 100 m. Maximium allowed distance of CAT6 Ethernet cable between two GPeR devices is up to 210 m (depending on cable quality). PoE in 802.3af/at. PoE input voltage 24-57 B. poE out 802.3af/at. Voltage drop on the cable and on GPeR units needs to be taken into account when calculating PoE-in possibility,
MikroTik GPeR-IP67-Case, IP68 outdoor enclosure for the GPeR. It can be easily mounted on walls and poles. the enclosure has an IP68 rating with protection from immersion in water, as well as protection from dust.
MIK-RB-POE, Mikrotik PoE injektor, Ethernet Speed: 10/100 Mbps, Low-cost passive PoE base unit for powering passive PoE devices over ethernet. Simply connect your power source to the injector, and then use an ethernet cable to connect the injector to the RouterBOARD device. Helps reducing number of wires that lead up the tower, and in other situations.
For using with RouterBOARDS that support 10-28V PoE powering, input needs to be at least 18V to accomodate any losses in cables.
Mikrotik RB-GPOE, Gigabit PoE injek. LED, The new MikroTik Gigabit PoE adapter for powering any RouterBOARD over Gigabit Ethernet. Simply connect your power source and then use an ethernet cable to connect the injector to the RouterBOARD device.
Helps reducing number of wires that lead up the tower.
For using with any RouterBOARD that supports 18-57V PoE.
Planet POE-162S, IEEE 802.3at Gigabit High Power over Ethernet Splitter that can split the 52 ~ 56V DC over the Ethernet cable into selectable 12V or 24V DC power output. Supports a maximum of 25.5 watts of input power. Input Power 802.3at PoE+ (52 ~ 56V DC), Output Power 12V / 24V DC Selectable through DIP Switch, Passive 10/100/1000Mbps Duplex Mode Support
TP-Link POE10R, PoE Splitter 802.3af compliant, Selectable power output to deliver 12V, 9V or 5V Direct Current, Gigabit speed support, can work with all IEEE 802.3af PoE compliant PSE (Power Source Equipment) or PoE Supplier Adapter
Ubiquiti Networks POE-48-24W-G, PoE adapter 48V/0,5A 24W, Gigabit Lan Port, includes power cable (EU), The POE-48 features earth grounding/ESD protection, and power LED, PoE power on Pins 1, 2, 4, 5 (+) and
Pins 7, 8, 3, 6 (-)